Lumber Cost Calculator
Use this free lumber cost calculator to estimate the cost of framing, pressure-treated and southern yellow pine boards from the size, length and number of boards, with board feet worked out for you. Quick answer: Home Depot listed 2×4×8 ft studs at $4.15–$4.65 and a pressure-treated 2×4×8 at $4.48–$4.88. See prices by type and size, actual lumber dimensions and the pressure-treated lumber guide.
Prices are Home Depot website listings seen October 31, 2026 · Where there is no listing for your size, the price is estimated from per-board-foot prices · Type your own price to override · Confirm with your supplier
Planning estimate, not a quote. Store prices vary by location and change often. Cedar, redwood, oak and composite are not priced.
Quick Answer: How Much Does Lumber Cost?
- A framing stud: 2×4×8 ft studs were listed at $4.15–$4.65 on Home Depot’s website, and a pressure-treated 2×4×8 at $4.48–$4.88.
- Bigger boards: a pressure-treated 2×6×8 was $9.68, a 2×8×8 $12.88, a 4×4×8 post $10.78, and a southern yellow pine 2×10×12 $19.12.
- Per board foot: those listings work out to about $0.78–$1.10 per board foot for untreated framing lumber and $0.84–$1.42 for pressure-treated southern pine (our arithmetic, leaving out 1-by boards, which run higher per board foot).
- Wholesale trend: Gordian data reported by BD+C put framing lumber at $916.62 per thousand board feet in Q2 2026, up 5.11% from the prior quarter and 4.21% from a year earlier.
Retail lumber is priced per piece and changes often, so use the calculator for a planning range and a local supplier’s quote for a real one.
Understanding the Calculator Inputs
Lumber Size and Length
Pick the nominal size, the name lumber is sold under (2×4, 2×6 and so on). Board feet are figured from the nominal size, which is how Lowe’s describes the calculation: nominal thickness times width times length. When you work out coverage, use the actual size in the table below.
Type
The calculator prices three types for which we found retail listings: untreated SPF or whitewood framing, untreated southern yellow pine, and pressure-treated southern pine. We did not find usable listings for cedar, redwood, oak or composite boards, so they are not priced here.
How the Price Is Found
If we saw a listing for your exact type, size and length, the calculator shows that price (or the range, where we saw more than one). If not, it estimates from the per-board-foot price of the listings we do have, and says so under the result. Type your own price per board to override either.
Waste Factor
The waste options are our own planning defaults, not a published standard: 10% for straightforward cuts, 15% or 20% for angles and curves. Cut lumber usually cannot be returned, so round up.
3 Lumber Cost Examples
These use prices we saw on Home Depot’s website. Piece counts are our own simple arithmetic and are not plans.
Example 1: Framing a 20 ft Wall
Studs: 20 ft × 12 ÷ 16 + 1 = 16. Double top plate: 40 ft ÷ 8 = 5 boards. Bottom plate: 20 ft ÷ 8 = 2.5, so 3 boards.
Untreated 2×4×8 (16 studs + 5 top plate boards = 21) at Home Depot’s $4.15–$4.65:21 × $4.15–$4.65 = $87.15–$97.65
Treated bottom plate, 3 pressure-treated 2×4×8 at $4.48–$4.88:3 × $4.48–$4.88 = $13.44–$14.64
Total lumber:$100.59–$112.29 before waste, door openings, fasteners and sales tax. With 10% waste on the 24 boards (27 boards) it is about $112–$126. Check with your building department whether the bottom plate on a slab must be treated. Use our Framing Calculator for a stud count.
Example 2: Posts and Rails for a 50 ft Fence
50 ÷ 8 = 6.25, so 7 bays and 8 posts. Rails: 7 bays × 2 = 14 boards (8 ft rails).
8 pressure-treated 4×4×8 posts at $10.78:8 × $10.78 = $86.24
14 pressure-treated 2×4×8 rails at $4.48–$4.88:14 × $4.48–$4.88 = $62.72–$68.32
Total posts and rails:$148.96–$154.56. Pickets, concrete and hardware are extra. Post depth and spacing depend on your fence height and local rules. For the full fence, use our Fence Cost Calculator.
Example 3: Joists, Rims and Posts for a 10 × 12 ft Deck
12 ft × 12 ÷ 16 + 1 = 10 joists (2×8×10). Two rim boards along the 12 ft sides (2×8×12). Four 4×4×8 posts.
Priced from the listings:10 × $17.28 = $172.80 · 2 × $19.68 = $39.36 · 4 × $10.78 = $43.12
Total:$255.28, before the beam, ledger, decking, hardware and footings. Joist size and spacing must come from your deck design and local code, not from this example. See our Deck Cost Calculator.
Lumber Sizes and Actual Dimensions
The Southern Pine Inspection Bureau explains that nominal sizes come from the board before drying and surfacing. Lumber shrinks as it dries and surfacing removes more, and the standard (Voluntary Product Standard PS 20) sets the minimum dressed sizes. For 2×4 and 2×6 the width is about ½ inch less than nominal, and for 2×8, 2×10 and 2×12 about ¾ inch less.
| Nominal size | Actual size | BF, 8 ft board | BF, 12 ft board |
|---|---|---|---|
| 2×4 | 1½" × 3½" | 5.33 | 8 |
| 2×6 | 1½" × 5½" | 8 | 12 |
| 2×8 | 1½" × 7¼" | 10.67 | 16 |
| 2×10 | 1½" × 9¼" | 13.33 | 20 |
| 2×12 | 1½" × 11¼" | 16 | 24 |
| 4×4 | 3½" × 3½" | 10.67 | 16 |
| 1×4 | ¾" × 3½" | 2.67 | 4 |
| 1×6 | ¾" × 5½" | 4 | 6 |
| 1×8 | ¾" × 7¼" | 5.33 | 8 |
Example of why actual size matters: a 12 ft wide deck is 144 in. wide. At the actual 5½ in. width of a 2×6, that is 144 ÷ 5.5 = 26.2, so 27 boards. Using the nominal 6 in. gives 24 boards, three short (our arithmetic, before gaps and waste).
Lumber Prices by Type and Size
Listed prices on Home Depot’s website, checked October 31, 2026. Store prices vary by location and change often. On the listings we saw, the “buy 50 or more” price was about 10% lower (a $4.15 stud was $3.74, and a $4.48 treated 2×4 was $4.03). Where we saw more than one listing for the same board, we show the range.
SPF / Whitewood Framing (Untreated)
| Board | Board feet | Listed price | Per board foot |
|---|---|---|---|
| 2×4 × 8 ft | 5.3 | $4.15–$4.65 | $0.78–$0.87 |
| 2×4 × 10 ft | 6.7 | $7.36 | $1.10 |
| 2×4 × 12 ft | 8 | $8.84 | $1.10 |
| 2×4 × 16 ft | 10.7 | $9.07 | $0.85 |
| 2×6 × 12 ft | 12 | $12.92 | $1.08 |
Southern Yellow Pine (Untreated)
| Board | Board feet | Listed price | Per board foot |
|---|---|---|---|
| 2×4 × 16 ft | 10.7 | $6.82 | $0.64 |
| 2×8 × 8 ft | 10.7 | $10.25 | $0.96 |
| 2×8 × 10 ft | 13.3 | $12.82 | $0.96 |
| 2×8 × 12 ft | 16 | $15.38 | $0.96 |
| 2×8 × 16 ft | 21.3 | $21.12 | $0.99 |
| 2×10 × 8 ft | 13.3 | $12.96 | $0.97 |
| 2×10 × 10 ft | 16.7 | $15.73 | $0.94 |
| 2×10 × 12 ft | 20 | $19.12 | $0.96 |
| 2×10 × 14 ft | 23.3 | $20.93 | $0.90 |
| 2×10 × 16 ft | 26.7 | $26.56 | $1.00 |
| 2×10 × 20 ft | 33.3 | $30.92 | $0.93 |
Pressure-Treated Southern Pine
| Board | Board feet | Listed price | Per board foot |
|---|---|---|---|
| 2×4 × 8 ft | 5.3 | $4.48–$4.88 | $0.84–$0.92 |
| 2×4 × 10 ft | 6.7 | $8.38 | $1.26 |
| 2×4 × 12 ft | 8 | $10.08 | $1.26 |
| 2×4 × 16 ft | 10.7 | $14.78 | $1.39 |
| 2×6 × 8 ft | 8 | $9.68 | $1.21 |
| 2×8 × 8 ft | 10.7 | $12.88 | $1.21 |
| 2×8 × 10 ft | 13.3 | $17.28 | $1.30 |
| 2×8 × 12 ft | 16 | $19.68 | $1.23 |
| 2×8 × 16 ft | 21.3 | $26.68 | $1.25 |
| 2×10 × 8 ft | 13.3 | $14.78 | $1.11 |
| 2×12 × 8 ft | 16 | $22.78 | $1.42 |
| 4×4 × 6 ft | 8 | $10.28 | $1.28 |
| 4×4 × 8 ft | 10.7 | $10.78 | $1.01 |
| 4×4 × 10 ft | 13.3 | $16.58 | $1.24 |
| 4×4 × 16 ft | 21.3 | $27.88 | $1.31 |
| 1×4 × 8 ft | 2.7 | $4.78 | $1.79 |
| 1×6 × 8 ft | 4 | $7.18 | $1.79 |
| 1×8 × 8 ft | 5.3 | $8.88 | $1.67 |
Per Board Foot, From the Listings Above
| Type (Home Depot listings) | Listings used | Range per board foot |
|---|---|---|
| SPF / whitewood framing (untreated) | 7 | $0.78–$1.10 |
| Southern yellow pine (untreated) | 11 | $0.64–$1.00 |
| Pressure-treated southern pine (2-by and 4×4) | 16 | $0.84–$1.42 |
Species costs differ a lot. For example, Home Depot listed a rough-green western red cedar 2×10×12 ft at $78.68, against $19.12 for a southern yellow pine 2×10×12. That is one listing for each, so treat it as an illustration, not an average. For a deck surface see our Composite Decking Cost Calculator and Deck Boards Calculator.
Lumber Cost per Square Foot of Surface
For boards that cover a surface, divide the price by the area one board covers. Home Depot listed a pressure-treated 5/4×6×8 ft decking board at $6.88–$9.38. Taking the board as about 5.5 in. wide, it covers 8 ft × 5.5 ÷ 12 = 3.67 sq ft, so $1.88–$2.56 per sq ft before gaps and waste (our arithmetic). Framing is different: studs, joists and rafters are priced per piece, and how many you need depends on spacing and span, so a per-sq-ft figure for a whole frame would depend on your design. Use our Framing Calculator, Board Feet Calculator and Plywood Calculator to count what you need.
Pressure-Treated Lumber Guide
The Southern Forest Products Association’s treated lumber guide groups treated wood by use category. Match the category on the tag to the job.
| Use category (SFPA) | Described as | Examples SFPA gives |
|---|---|---|
| UC3B | Above ground, exposed | Sawn decking, deck joists and beams not subject to frequent wetting, railings, stair stepping |
| UC4A | Ground contact, general use | Posts, deck joists and beams in ground contact, stair stringers |
| UC4B | Ground contact, heavy duty | Critical components with high decay potential, such as salt-water splash or continuous wetting |
| UC4C | Ground contact, extreme duty | Critical structural components in severe environments |
| UC5A / 5B / 5C | Marine, brackish and salt water | Northern, central and southern waters |
Fasteners and Hardware
- SFPA says codes generally call for hot-dipped galvanized steel (ASTM B695), type 304 or 316 stainless steel, silicon bronze or copper.
- Electroplated galvanized fasteners and connectors are typically not accepted for exterior use.
- Aluminum should not touch wood treated with dissolved copper preservatives.
- Fasteners and connectors used together should have the same metallic composition, to avoid galvanic corrosion.
Moisture, Finishing and Handling
- Dimension lumber is dried to 19% moisture content or less before treatment, but can exceed 50% when it leaves the treating cylinder, and most treated southern pine is delivered without redrying.
- Treated decking shrinks and swells with wetting and drying.
- SFPA gives no set wait time before finishing. Follow the paint or stain maker’s instructions, and let the wood dry first.
- Cuts and holes that go through the treated zone need field treatment under AWPA M4.
- Do not burn treated wood in open fires, stoves, fireplaces or residential boilers, and wash your hands after working with it.
Why Lumber Prices Change
Wholesale trend. BD+C reported on April 24, 2026 that Gordian’s April 2026 data put framing lumber at $916.62 per thousand board feet, up 5.11% from the prior quarter and 4.21% from a year earlier, after two quarters of decline.
Trade policy. A 10% Section 232 tariff on softwood timber and lumber has applied to imports since October 14, 2025, stacked on any antidumping and countervailing duties, according to law firm Sandler, Travis & Rosenberg. Global Affairs Canada reports that on October 14, 2026 the US Department of Commerce announced final results of its seventh administrative reviews of antidumping and countervailing duties on Canadian softwood lumber, with combined rates of 31.11% (Canfor), 25.55% (Resolute), 20.02% (West Fraser) and 24.75% (all others), taking effect once published in the Federal Register.
We do not forecast prices. How much of any change reaches the price on a store shelf depends on the retailer and your region, so check a current quote before you order a large amount.
Common Buying Mistakes
- Counting coverage with nominal sizes. A 2×6 is about 5½ in. wide, not 6.
- Using untreated lumber where the tag calls for treated. SFPA lists posts and joists in ground contact under UC4A, which means treated wood.
- Wrong fasteners in treated wood. Use the hardware types SFPA lists above.
- Ordering the exact count. One bad board or a design change means another trip. Add a waste allowance.
- Pricing by board foot at the store. Softwood framing lumber is listed per piece, so check the price of the actual board and length you need.
- Budgeting from an online estimate. Get a quote from your local supplier with a full cut list for anything large.
How We Estimate Costs
Board feet: BF per board = nominal thickness (in.) × nominal width (in.) × length (ft) ÷ 12. Total BF = boards × BF per board.
Cost: Total cost = boards × price per board, where boards = quantity × waste factor, rounded up. The price per board is a listed price for your exact type, size and length when we have one. Otherwise it is the per-board-foot range of our listings for that type (same size if we have it) times the board’s BF.
Data: the prices come from Home Depot’s website listings checked October 31, 2026. We did not survey other stores or lumber yards and we do not claim a national average. The per-board-foot figures, piece counts and waste options are our own arithmetic and defaults.
Not included: hardware, concrete, sheathing, delivery, tax, labor and other species. For plywood or sheet goods use our Plywood Calculator.
Frequently Asked Questions
Plan your full lumber project with these free calculators.
Measurement Tools
Material Calculators
- Home Depot — 2x4 framing studs: listed prices for 2×4 studs (checked October 31, 2026).
- Home Depot — 2x4 and 2x8 dimensional lumber: listed prices for SPF and southern yellow pine boards.
- Home Depot — 2x10 dimensional lumber: listed prices for 2×10 boards by length.
- Home Depot — 12 ft bulk-pricing lumber: listed prices for 12 ft 2×4 and 2×6 SPF.
- Home Depot — pressure-treated 2x4 and 2x8: listed prices for treated lumber.
- Home Depot — 8 ft treated boards and decking: listed prices for treated 2×6 to 2×12, 1-by boards and decking.
- Home Depot — deck posts: listed prices for treated 4×4 posts.
- Southern Forest Products Association — Pressure-Treated Southern Pine: use categories, fasteners, moisture, field treatment and handling.
- Southern Pine Inspection Bureau — Nominal vs. Actual Lumber Sizes: why actual sizes are smaller than nominal, and the width rules.
- Lowe’s — Nominal and Actual Lumber Sizes: why lumber is smaller than its name, and how board feet are calculated.
- Building Design + Construction — Framing lumber costs spike 5.11% in Q2, according to Gordian data: wholesale framing lumber price and change.
- Sandler, Travis & Rosenberg — New Section 232 tariffs on timber, lumber and derivative products: the 10% softwood lumber tariff and its start date.
- Global Affairs Canada — Softwood lumber: recent developments: the October 14, 2026 final results on antidumping and countervailing duty rates.
Retail prices are listings seen on one retailer’s website, vary by store and change often, and are not quotes. Per-board-foot figures, piece counts, waste options and the 5/4 decking coverage are our arithmetic. ConstructlyTools does not have a paid relationship with any retailer or brand mentioned on this page.
Prakash
Prakash is the founder and editor of ConstructlyTools. He researches, develops, and maintains construction calculators, material estimators, cost guides, and DIY planning resources designed to help homeowners, contractors, and builders make informed project decisions.
Every calculator and guide is researched using trusted industry references, published building standards, manufacturer specifications, and reliable construction pricing sources. Each page is reviewed for formula accuracy, pricing methodology, readability, and practical usefulness before publication and is updated regularly as standards or market prices change.
Every calculator and article published on ConstructlyTools is reviewed by the editor for formula accuracy, pricing methodology, readability, and practical usefulness before publication. We use AI tools to help draft and format some content; every figure and formula is checked by the editor before publication. Content is updated whenever construction pricing, industry standards, or building code references significantly change.
This page was researched, written, and reviewed in accordance with our Editorial Policy.
